How small can a pocket door be?

Standard nominal measurements for such doors are 7-1/2 feet, 8 feet, or nine feet wide and either the standard 6’8” tall for most rooms or 8′ tall for rooms with raised ceilings.

How much space is needed for a pocket door?

Check That You Have Enough Space

A pocket door requires a “sleeve” inside the wall to retract into. For a traditional 32-inch-wide interior door, you’ll need at least 66 inches of linear wall space: 32 inches for the door and the rest for the housing.

What sizes do pocket doors come in?

Calculating the dimensions of a sliding pocket door

A standard sliding pocket door has the same sizes as a corresponding hinged door. It typically measures 30″ or 36″ in width and 80″ in height. It is also possible to build customized solutions having very large or very small passage sizes.

Can you put a pocket door in a 2×4 wall?

Pocket doors are really convenient when you are tight on space, but they aren’t always the easiest doors to use. … This is especially the case on pocket doors that are taller than the standard 6’8″. The reasoning is a 2×4 wall really has no room for framing other than a 1×2 or 1×4.

IT IS INTERESTING:  What is a pocket sliding glass door?

Can a pocket door be shortened?

Pocket Door Frame kits contain all necessary hardware for a single pocket door installation in a 2×4 stud wall (door, jambs, drywall, door locks, door pulls, hidden pocket door guide kit NOT included). All frames CAN be cut down to fit smaller size door.

How much room do you need for a 36 inch pocket door?

The rule of thumb for sizing the opening is door width times 2 plus 1 ¾”. For example, to install a 36” pocket door you’re going to need an opening that is 73 ¾” wide – (2 X 36 = 72, 72 + 1 ¾” = 73 ¾”) while installing a 32” door would require an opening 65 ¾” wide.

Are pocket doors worth it?

Pocket doors can be a beautiful space saving architectural feature in your home. However, that being said, they do have drawbacks that may not make them the best choice for some homeowners. … Spend the extra money and install solid doors. While they are heavier and harder on the hardware, they are much more durable.

Are pocket doors expensive?

Pocket Doors Cost

During a new construction, pocket doors will cost between $500 and $1,000. As part of a remodeling project, their cost will be in the $1,000 to $3,500 range. These prices reflect both parts and labor. These doors hide inside a wall cavity instead of swinging out from a hinge.

How much does it cost to install a pocket door?

The average cost range to install a pocket door is between $600 and $1,500, with most people paying around $700 for a new 30-inch solid wood door. It costs around $400 to install a hollow core door in new construction and $4,250 to install double-glass pocket doors in existing walls.

IT IS INTERESTING:  How do I measure an exterior door for replacement?

Is it hard to install a pocket door?

If you have simple tools, you can install the pocket door frame and hardware with little difficulty. Installing the door into the pocket is also fairly easy to do. … The most important part of installing a pocket door is making sure the rough opening is square, plumb and in the same plane.

Can you put a pocket door in an existing wall?

To install a pocket door in an existing wall, you have to remove drywall, and it’s easier to uncover the entire wall instead of trying to work in a limited opening. … You’ll need to set new king studs and trimmers, place the header and install cripple studs between the header and the top plate of the wall.

Do pocket doors have a bottom track?

Typically, pocket doors have an upper track only, but if you plan ahead you can have a bottom track. This gives the sliding door a robust fixing and makes it less likely to flap about when in the open position. It involves fixing the track into the floor — one way to do this is with a router in a timber floor.

Can you hang a picture on a pocket door wall?

If you were building a home and you knew you might be installing shelves or hanging heavy pictures on a pocket door wall, I’d recommend that you glue and screw pieces of a half-inch plywood to the back of the drywall to cover the thin studs that create the pocket for the door.

What can I use instead of a pocket door?

Tight Quarters? 10 Smart Space-Saving Door Solutions

  • Pocket Doors. 1/10. …
  • Barn Doors. 2/10. …
  • Glass Bifold Doors. 3/10. …
  • Pivot Doors. 4/10. …
  • Shoji Doors. 5/10. …
  • Dutch Doors. 6/10. …
  • Garage Door. 7/10. …
  • French Accordion Doors. 8/10.
IT IS INTERESTING:  Why doesn't my garage door close when it's cold?

Can you cut down the height of a pocket door?

Depends on the door but most of the time yes. If the existing door is below standard height it’s probably too low to begin with, and also something to remember is if you cut too much off the bottom and it’s hollow core you will cut all the rail out leaving the bottom empty.

How do you fix a pocket door that rubs?

If you see the telltale rub marks, then either the door is warped, or the studs are bowed. Either way, though, one fix is to replace the door. If the door is warped, a new door of the same thickness may fix the problem. If the studs are bowed, you can replace the door with a thinner one (swap a 1-3/4 in.

 Profil Doors