# What size door fits in a 30 inch opening?

Contents

So, if you have a bedroom door that is 30″ wide (which is considered a 2/6 or 2′-6″ door) just add 2″ to the width and frame it 32″ wide. The height is 80″ (which is considered 6/8 or 6′-8″) add 2-1/2″ to the actual door height and frame it 82-1/2″ high.

## What size opening do I need for a 30 inch door?

Measurements For Rough Opening

Rough Opening Width Rough Opening Height Door Size to Order
29.75″ – 31″ 81.5″ – 83″ 28″
31.75″ – 33″ 81.5″ – 83″ 30″
33.75″ – 35″ 81.5″ – 83″ 32″
35.75″ – 37″ 37.75″-39″ 81.5″ – 83″ 34″ 36″

## How wide is a 30 inch Prehung door?

In the building trades, a 30-inch door is called a “2-6” door, meaning 2 feet, 6 inches wide, or 30 inches. If you haven’t framed a door before, this project provides an excellent opportunity to learn.

IT IS INTERESTING:  What kind of saw do you use to cut door jambs?

## How much smaller should a door be than the opening?

Check the door fit. Ideally, there should be a gap of about 1/8 inch at the top and along each side, and about 3/8 inch at the bottom.

## Are 30 inch doors actually 30 inches?

Called a 6/6 door, it’s reserved for closet and utility doors. Standard interior door width is 32 inches. This is the minimum width required for a passage door. You may also find a few narrower doors in stock, including 30 inches, 28 inches, and 24 inches.

## What size door do I need for a 32 inch opening?

So, if you have a bedroom door that is 30″ wide (which is considered a 2/6 or 2′-6″ door) just add 2″ to the width and frame it 32″ wide. The height is 80″ (which is considered 6/8 or 6′-8″) add 2-1/2″ to the actual door height and frame it 82-1/2″ high.

## What is the rough opening for a 32 inch Prehung door?

Rough Opening for 32 Inch Door

For example a two-foot, eight inch (32”) by six feet, eight inch high (80”) prehung door, would require a rough opening width of 34 inches and a height of 82 inches.

## What are standard door sizes?

The height for all passage doors must be a minimum of 80 inches and the standard width sizes for interior doors are 24”, 28”, 30”, 32” and 36”. The minimum recommended door width to allow persons with disabilities’ to pass through is 36 inches.

## How much space should be between door and frame?

The frame should be 3/16″ wider than the slab (1/16″ clearance on the hinge jamb and 1/8″ clearance on the strike jamb) and tall enough (usually 1/4″ – 1/2″ taller) to allow 1/8″ clearance on the head jamb and allow the slab to operate without rubbing on any flooring.

IT IS INTERESTING:  Can I use wd40 on my garage door wheels?

## How much space should be between rough opening and door jamb?

There should be a 1/8” gap between the latch-side jamb and the door slab edge at the top and bottom of the door only. Drive a 3” installation screw through the vacant hole in each hinge, through the jamb, shims and into the stud.

## How much bigger should door jamb be than the door?

A basic rule of thumb is to make the rough opening 2 inches wider and 2 1/2 inches taller than the door. This leaves room for the prehung door unit, space for shims to plumb and straighten the jambs, and clearance below the door for carpeting or other flooring material.

## How wide is a 30 inch door with frame?

32-1/2 inches. The rough framing should be 2-1/2 inches wider than the door itself. That leaves room for the 3/4 inch finish frame on each side of the door, and then 1/2 inch on each side for the shims between the finish frame and the rough frame.

## What’s the actual size of a 36 inch door?

3’0″ (36 Inch) Door Width (Actual Size 35-3/4″) by Door Closers USA.

## How big should the opening be for a 36 inch door?

Standard Sizes

A 36” x 80” pre-hung single door will use a rough opening of approximately 38-1/2” x 82-1/4” to fit. Always remember to square up your door before you nail the frame in place to assure it will close properly.