Best answer: Why is my Kwikset lock blinking orange?

Amber flashes mean it is locked, while green flashes mean it is unlocked, and red means low battery.

Why is my Kwikset lock not working?

Take the battery pack out of the unit and depress the button labeled “Program” three times if the unit doesn’t operate properly after installation or fails to open with a key. Allow ten seconds to elapse, then hold down the “Lock” button while reinstalling the battery pack.

How do I reset my Kwikset lock after changing the battery?

Make sure there are no lithium NiCad batteries in use. If you’re replacing the battery because of a low battery warning, press and hold the Program button for five seconds, then press and hold button A for five seconds. Replace the battery pack. The lock will then restart.

Why is my Kwikset lock beeping 10 times?

If you hear 1 long beep, it means that the turnpiece rotated to locked position. If you hear 10 short beeps and 10 short red flashes, it means low battery. If you hear 15 long beeps and 15 long red flashes, it means 3 incorrect user codes entered.

IT IS INTERESTING:  Question: How much do bifold exterior doors cost?

How do you reset a Kwikset lock?

1 Factory Reset

  1. Open your door.
  2. Extend the latch bolt.
  3. Slide up the cover to open the back of your lock, exposing the buttons beneath.
  4. Push and hold the reset button for 10 seconds, until the lock beeps.
  5. The light ring will flash red, then spin amber.
  6. The lock has now been restored and is ready to be set up again.

Why won’t my Kwikset lock stop beeping?

The lock should beep twice when it unlocks and once when it locks. It will also beep if there is a warning such as a low battery or a jammed bolt. To turn the beeping sound off: … Reinstall the battery cover.

What happens if Smart Lock battery dies?

If your smart device battery dies, you can always use the Kevo fob or a standard key to unlock your door. You can also sign into the app on another supported smart device, and your eKeys will be instantly transferred to it. As with any lock, we recommend you have access to a backup key.

What is the master code for Kwikset lock?

The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open.

How long do Smart Lock batteries last?

4xAA batteries are expected to last up to a year based on 10 entries per day. However, misaligned doors where the lock faces resistance during lock/unlocking will shorten the battery life since the motor uses more power to exercise the latch.

IT IS INTERESTING:  Which door lock is best?

Why is my door lock beeping?

If your Electronic Door Lock is beeping and the buttons are flashing red, this means that there’s been some kind of error or the batteries are low. If the batteries have already been changed and you still see a red flashing light when you try to use the lock, there could be an error with the lock.

How do I unlock my Kwikset SmartCode?

Kwikset SmartCode locks are available as lever sets or deadbolt locks. Our sample is a deadbolt version which has a motor-driven deadbolt. Unlocking from the inside of the door is done manually by turning the thumb turn. Locking and unlocking from the outside can be done automatically by an electric motor.

How do I remove a code from Kwikset lock?

Delete A User Code:

  1. Make sure the door is open.
  2. If you have not enabled a programming code, press and release the program button. You will hear two beeps. …
  3. Press 2 to delete a user code. …
  4. Press Kwikset.
  5. Enter the user code you wish to delete. …
  6. Enter the user code again.
  7. Press Kwikset.

How do you reset a Kwikset 910 lock?

How to perform a factory reset:

  1. Remove the batteries.
  2. Press and hold the lock button on the keypad.
  3. Place the batteries back in (while still holding the button)
  4. The lock will beep three times over the course of 15 seconds or so. After the 3rd beep release the button.

22.08.2014

How do you reset a Kwikset lock 913?

How do I program my SmartCode 913 lock?

  1. Open the door.
  2. Remove battery cover.
  3. Press the program button once.
  4. Enter new user code.
  5. Press lock button.
  6. If programming is successful the keypad will flash green once, and you will hear one beep.
IT IS INTERESTING:  How do I remove the blend door actuator?
 Profil Doors