How do I open the door on my Whirlpool Duet washer?

How do I unlock my front load washer door?

How To Open A Front Load Washing Machine Door After Starting The Wash Cycle

  1. How to unlock washer door? …
  2. Within at least 5 minutes of pressing the START/WASH button, press the START/PAUSE button to unlock the washer door. …
  3. Now open the washing machine door once unlocked and add or remove any extra clothing.

4.04.2018

What do you do when your Whirlpool washer won’t unlock?

How to Manually Unlock Whirlpool Washer Door Lock

  1. Unplug your washing machine from the electric outlet board. Wait for 3 to 5 minutes.
  2. Take a screwdriver. Remove your washer’s bottom panel and pull it away.
  3. Reach the door lock through the open panel. Locate the door latch under the locking mechanism.

28.10.2020

What do you do when your washing machine door wont open?

The most common cause is water left in machine. Try running a spin/drain cycle. If this fails, the machine can be drained by placing the washing machine drain hose lower than the drum (into a bucket or tray). The door interlock has simply jammed.

IT IS INTERESTING:  Why do my new door hinges squeak?

How do you manually unlock a Whirlpool front load washer?

Press the “Drain and Spin” button on the washer’s control panel to attempt to unlock the machine. This may drain any excess water that could cause the machine to remain locked. Once the “Drain and Spin” cycle completes, the door should unlock.

How do I reset my Whirlpool front load washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

What does it mean when my Whirlpool washer says LoC?

If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock, and need to de-activate it to allow the washer controls to function.

How do you fix a Whirlpool washer that won’t drain?

What to Do When Your Washing Machine Won’t Drain

  1. Perform a Master Reset. Unplug your washer for about one minute. …
  2. Test the Lid Switch Assembly. …
  3. See if the Drain Hose is Kinked. …
  4. Check the Drain Hose or Pump for Clogs. …
  5. Clean out the Coin Trap. …
  6. Check the Water Level Control. …
  7. Schedule Washing Machine Repair.

29.10.2019

How do you bypass a washing machine door lock?

How to Bypass a Washing Machine Lid Lock

  1. Turn off the washer and unplug the appliance. …
  2. Locate the retaining tabs and/or screws that hold the top horizontal panel down. …
  3. Look for the lid lock switch on the underside of the top panel and where it fits into the appliance. …
  4. Put the lid back down and plug the washing machine back into the electrical outlet.
IT IS INTERESTING:  How much does it cost to Restain wood doors?

Why will my washing machine not turn on?

One of the most common reasons for a washing machine refusing to start is the door, the interlock to be precise. … If it is a problem caused by your machine overheating then simply give it some time to cool down, unplug the machine leave it for a few hours and then try plugging it in again.

Why will my washer not start?

If your washer will not start, be sure the switch is being pressed. If the lid switch is being pressed but no power is being supplied to the washers motor, then the switch is most likely bad. To test the switch, turn off power to washer and remove the wires from the lid switch.

How do you reset a front load washer?

How to reset the washing machine:

  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.
 Profil Doors