How do you reset a Kwikset 909?

See the online Programing and Troubleshooting Guide. A factory reset will delete all codes associated with the lock. 3 Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.

How do I reset my Kwikset SmartCode 909?

How to restore default settings on my Signature Series or SmartCode Deadbolt? Perform a factory reset

  1. Remove battery pack.
  2. Press and HOLD the Program button while reinserting the battery pack. …
  3. Press the Program button once more. …
  4. Perform the door handing process again to teach the lock the orientation of the door.

How do I delete all codes on Kwikset SmartCode 909?

How do I delete all user codes on my SmartCode?

  1. Keep door open. Press the Program button once. …
  2. Press Lock button once.
  3. Enter Mastercode.
  4. Press Lock button once.
  5. Press “9” six times.
  6. Press Lock button once.
  7. Press “9” six times.
  8. Press Lock button once. If programming is successful, the keypad will flash green once with one beep.

How do you change the code on a Kwikset 909 electronic lock?

While the door is open, press the “Program” keypad button located on the interior side of the door. Enter a four to eight digit security code that you can easily remember on the outside electronic lock keypad. Press the “Lock” keypad button at the center of the SmartCode keypad.

IT IS INTERESTING:  Frequent question: Does Mercedes have soft close doors?

How do you program a Kwikset 909?

(1) Hold LOCK button on keypad while (2) inserting the battery pack into the interior. The lock will automatically sense the handing of the door and will extend & retract deadbolt latch. Two beeps will sound in approximately 30 seconds to confirm successful installation.

How do I factory reset my Kwikset SmartCode?

How to restore default settings on my SmartCode lever? Perform a factory reset

  1. Remove battery pack.
  2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
  3. Press the Program button once more.

How do you reset a Kwikset 913 Deadbolt?

A factory reset will delete all codes associated with the lock. 3 Press the Program button once more. In 20 seconds, when the LED flashes green and you hear one beep, the lock has been reset.

How do you reprogram a Kwikset lock?

How do I reset a code on my Powerbolt?

  1. Insert functioning key & turn 1/4 turn clockwise.
  2. Insert & remove the SmartKey learn tool. Remove functioning key.
  3. Insert new key & turn 1/2 turn counter-clockwise. Done. Your lock is now re-keyed! “”

What is the master code for Kwikset lock?

The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open.

Why is my Kwikset lock not working?

Take the battery pack out of the unit and depress the button labeled “Program” three times if the unit doesn’t operate properly after installation or fails to open with a key. Allow ten seconds to elapse, then hold down the “Lock” button while reinstalling the battery pack.

IT IS INTERESTING:  When God closes a door no man can open?

How do you reset a Kwikset door lock?

1 Factory Reset

  1. Open your door.
  2. Extend the latch bolt.
  3. Slide up the cover to open the back of your lock, exposing the buttons beneath.
  4. Push and hold the reset button for 10 seconds, until the lock beeps.
  5. The light ring will flash red, then spin amber.
  6. The lock has now been restored and is ready to be set up again.

How do you program a Kwikset 913?

How do I program my SmartCode 913 lock?

  1. Open the door.
  2. Remove battery cover.
  3. Press the program button once.
  4. Enter new user code.
  5. Press lock button.
  6. If programming is successful the keypad will flash green once, and you will hear one beep.
 Profil Doors