Question: How do I reset the master code on a Kwikset 913?

How do you reset a Kwikset 913 Deadbolt?

A factory reset will delete all codes associated with the lock. 3 Press the Program button once more. In 20 seconds, when the LED flashes green and you hear one beep, the lock has been reset.

How do I reset my Kwikset SmartCode master code?

How do I enable/delete the mastercode on my Smartcode?

  1. Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).
  2. Enter new Mastercode.
  3. Press Lock button once.
  4. Re-enter Mastercode.
  5. Press Lock button once. …
  6. Make sure switch #3 is on, and press the Program button once.

How do I delete all codes on Kwikset SmartCode 913?

How do I delete all user codes on my SmartCode?

  1. Keep door open. Press the Program button once. …
  2. Press Lock button once.
  3. Enter Mastercode.
  4. Press Lock button once.
  5. Press “9” six times.
  6. Press Lock button once.
  7. Press “9” six times.
  8. Press Lock button once. If programming is successful, the keypad will flash green once with one beep.
IT IS INTERESTING:  How do you make plain cabinet doors look good?

How do you reset a Kwikset lock?

1 Factory Reset

  1. Open your door.
  2. Extend the latch bolt.
  3. Slide up the cover to open the back of your lock, exposing the buttons beneath.
  4. Push and hold the reset button for 10 seconds, until the lock beeps.
  5. The light ring will flash red, then spin amber.
  6. The lock has now been restored and is ready to be set up again.

What is the master code for Kwikset lock?

The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open.

How do I reset my Kwikset SmartKey lock without key?

Kwikset Smartkey – Rekey without Existing key

  1. Remove the lock from the door. In this example we will be using a Kwikset Kevo as the example Smartkey. …
  2. Remove Retainer Clip. This clip keeps the lock cylinder inside the housing. …
  3. Remove Cylinder. …
  4. Remove Retainer Clip. …
  5. Remove Plug from Housing. …
  6. Line Up Wafers. …
  7. Insert New Key and Let Tab Go.

25.10.2019

How do I reset my Kwikset 910 lock code?

Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.

How do you reset the master code on a door lock?

This lock is preset at the factory to operate at 0-0-0-0.

  1. With dials at 0-0-0-0, pull out the shackle.
  2. Turn shackle counterclockwise 90 degree (1/4 turn)
  3. Continue pressing shackle down and turn another 90 degree (1/4 turn)
  4. Set the dials to your own combination.
IT IS INTERESTING:  Question: Can a door frame be load bearing?

How do you remove the code on a Kwikset lock 914?

How to delete a/all user code(s) on my Smartcode touchscreen?

  1. Keep door open. Press Program button once.
  2. Press Checkmark symbol once.
  3. Press Lock symbol once.

How do you unlock a Kwikset lock code?

To program the first user code:

  1. Press the button marked “program button” once.
  2. Using the keypad, enter a 4- to 8-digit code.
  3. Press the ‘LOCK” button to save the code.
  4. Extend the bolt by pressing- the “LOCK” button.
  5. Enter the new code number. The bolt should retract.

2.02.2012

How do I change my Kwikset lock code?

How do I add/delete a user code on my Powerbolt 2?

  1. Make sure the lock is unlocked and the door is open.
  2. Enter your Mastercode – for new install, default is 0-0-0-0.
  3. Press the lock button. You will hear one beep.
  4. Press 1.
  5. Press the lock button. You will hear one beep.
  6. Enter a new User Code. …
  7. Press the lock button. …
  8. Test the code: While your door is open, lock it.
 Profil Doors