What is the program button on Kwikset lock?

To set a code for the second user, press the SmartCode “Program” button twice to program a security code for the second user, such as a relative. Enter a four to eight digit security code on the outside electronic lock keypad and press the “Lock” button again.

How do you program a Kwikset door lock?

It is recommended that you change it to a code of your own.

  1. Make sure the lock is unlocked and the door is open.
  2. Enter your Programming Code – for new installation, default is 0-0-0-0.
  3. Press enter arrow. You will hear one beep.
  4. Press 4 .
  5. Press enter arrow. You will hear one beep.
  6. Enter a new Programming Code.

How do I delete the code on my Kwikset lock?

Delete A User Code:

  1. Make sure the door is open.
  2. If you have not enabled a programming code, press and release the program button. You will hear two beeps. …
  3. Press 2 to delete a user code. …
  4. Press Kwikset.
  5. Enter the user code you wish to delete. …
  6. Enter the user code again.
  7. Press Kwikset.
IT IS INTERESTING:  Your question: Are refrigerator doors supposed to be even?

How do you reset a Kwikset lock?

1 Factory Reset

  1. Open your door.
  2. Extend the latch bolt.
  3. Slide up the cover to open the back of your lock, exposing the buttons beneath.
  4. Push and hold the reset button for 10 seconds, until the lock beeps.
  5. The light ring will flash red, then spin amber.
  6. The lock has now been restored and is ready to be set up again.

Can you reset a Kwikset lock without original key?

Rekeying a Kwikset Smartkey without a key has been our most popular request. The Smartkey has several parts to it, and many locksmiths do not touch them without an existing key.

How do I reset my Kwikset 910 lock code?

Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.

How do you reset a Kwikset 910 lock?

How to perform a factory reset:

  1. Remove the batteries.
  2. Press and hold the lock button on the keypad.
  3. Place the batteries back in (while still holding the button)
  4. The lock will beep three times over the course of 15 seconds or so. After the 3rd beep release the button.

22.08.2014

How do you remove the code on a Kwikset lock 914?

How to delete a/all user code(s) on my Smartcode touchscreen?

  1. Keep door open. Press Program button once.
  2. Press Checkmark symbol once.
  3. Press Lock symbol once.
IT IS INTERESTING:  How do I unfreeze my car door latch?

How do you remove the code from a keypad lock?

Deleting User Codes

  1. Press the program button.
  2. Press the lock button.
  3. Enter user code to delete.
  4. Press lock button.
  5. Re-enter user code to delete.
  6. Press lock button.
  7. If successful, the keypad will flash green once and you will hear 1 beep (if switch #3 is on).

24.07.2017

Why is my Kwikset lock not working?

Take the battery pack out of the unit and depress the button labeled “Program” three times if the unit doesn’t operate properly after installation or fails to open with a key. Allow ten seconds to elapse, then hold down the “Lock” button while reinstalling the battery pack.

Why won’t my Kwikset lock won’t lock?

If there are no codes in the lock, the lock button will not lock the door. … The battery is too low to lock the door. This is indicated by the keypad flashing red three times with three beeps. Remove the batteries and replace with a fresh set.

How do you open a Kwikset Smart Lock?

Unlocking from the inside of the door is done manually by turning the thumb turn. Locking and unlocking from the outside can be done automatically by an electric motor. As the last number of a correct code is pressed on the keypad, the electric motor swings into action and retracts the deadbolt.

 Profil Doors