# Is there a left and right garage door spring?

Contents

On most garage doors, the spring on the left side of the center support bracket has a winding cone with red paint on it. This is a right wind spring. The spring on the right side of the bracket usually has black paint on the winding cone.

## Which way do you wind a garage door spring?

Determine the “hand” of the spring

View the end of each spring to determine its wind direction, or “hand.” If the end of the spring is pointing up on the right, it’s a right-hand wind. If the end is pointing up on the left, it’s a left-hand wind. Doors with two springs will always have a left- and a right-hand spring.

## How do I know what torsion spring I have?

Easy as 1, 2, 3, 4.

1. Step 1: Determine the Wind Direction. Look at the end of the spring to determine the wind direction. …
2. Step 2: Measure the Wire Size. Measure the length of ten or twenty coils of the spring that needs to be replaced, using inches. …
3. Step 3: Measure the Inside Diameter. …
4. Step 4: Measure the Overall Length.
IT IS INTERESTING:  What should I hang above my door?

5.12.2018

## Should my garage door have two torsion springs?

Torsion spring systems can use one or two springs. As a rule of thumb, a single garage door takes one torsion spring. A double-wide garage door takes two springs. However, if you have an exceptionally heavy single door, you may need two torsion springs.

## Does length of torsion spring matter?

Replacing a too-big or too-small torsion spring with the right size will balance the door and make it safe again. The door will rise with less effort and remain safely in place. The garage door opener may also need to be replaced if it has been damaged by springs that are too big or too small.

## Can you open a garage door with a broken spring?

Garage doors with broken springs should not be opened. Doors in this condition can be difficult to lift because the garage door opener loses the support springs provide in lifting and lowering the door. … We don’t recommend attempting to open a garage door with a broken spring but sometimes it’s an absolute emergency.

## How many turns on a 7ft garage door spring?

Raise the second bar 90 degrees and insert the first bar. This is “three.” Continue winding. If the spring shortens in length, unwind the spring and switch sides – the spring is on the wrong side. Otherwise, continue winding until you reach a count of “30.” This is 7 1/2 turns, which is normal for most 7′ garage doors.

## How many rotations do I need for a garage door spring?

A rule of thumb with springs is that four quarter turns equals a full revolution and the spring needs to be tightened a full revolution for every foot of door height (e.g. 7-1/2 foot door = 7 revolutions +2 (30 quarter turns). Click to see full answer.

IT IS INTERESTING:  Do ADA bathroom doors swing in or out?

## What do the colors mean on torsion springs?

The color code on a torsion spring indicates whether it is a “right wind” or “left wind” spring, with black indicating right wind and red indicating left wind. Beyond that the torsion spring is color coded so that technicians can determine the thickness, or gauge, of the wire.

## How many turns on a torsion spring?

A rule of thumb with springs is that four quarter turns equals a full revolution and the spring needs to be tightened a full revolution for every foot of door height (e.g. 7-1/2 foot door = 7 revolutions +2 (30 quarter turns).

## How much does it cost to replace spring on garage door?

Garage Door Spring Replacement Cost. Replacing garage door springs costs \$100 to \$300 on average. The springs alone typically run \$30 to \$75 each but you may find them as low as \$15 a piece and up to \$100 each. Commercial grade springs can run \$300 or more.

## Why do some garage doors only have one spring?

Why Was There Only 1 Spring Before? Most home builders cut corners in one area to make other areas of the home more appealing. Unfortunately, the garage door is an area of where they cut expenses by installing only one torsion spring on a standard 16’x7′ garage door when there really should be two.

## How much does it cost to replace a torsion spring?

A torsion spring replacement costs \$140 to \$350, while an extension spring replacement runs \$120 to \$200. The spring parts alone cost \$20 to \$70 each, and labor runs \$100 to \$200. *Prices are for standard 1 and 2-car garage doors. Springs for heavy-insulated wood doors cost an additional \$60 to \$100 for a set.

IT IS INTERESTING:  Your question: Which way does a dryer door open?