You can trim them down pretty much as much as you want. The problem you’re going to run in to (especially if you bought the 6 panel doors) is how uneven they can look when you trim them width wise. As others have said, your probably better off with solid wood doors or, even better, custom sized doors.
Can you trim bifold closet doors?
If you ordered a bifold door and find it’s a bit too long for the door’s height, it’s a simple matter to trim the door to fit. Installing carpet with a thicker nap can sometimes cause the bifold door to drag. As a house settles over time, you might also find you need to adjust the height of a bifold door.
Can you adjust bifold doors?
For Supreme bifold doors, you can adjust the height up or down using the bottom pivot and bottom intermediate carriers.
How much smaller should a bifold door be than the opening?
Bifold doors must be 1-1/2” shorter in height than the finished opening. This space is necessary for both the opening clearance and installation of hardware (rail and pivot hinges).
Can Masonite bifold doors be trimmed?
Just drill them after you cut and fit the door for either 2 3/8 or 2 3/4 backset. Now on the off chance you need to take an inch or more off the bottom you will lose that bottom piece of the frame. No biggee. Just clean up the piece of frame you cut off( chisel off the door skin) and glue it back in.
Is it hard to install bifold closet doors?
These doors are easy to open and are considered a space-saving option in smaller areas like bedrooms, pantries and hallways. Bifold doors and bifold door hardware come in a variety of styles and finishes to complement your home and are ideal if you’re looking to install closet doors.
Why do bifold doors drop?
As attractive and functional as bi-folding doors might be, they can fail. After years of daily use, doors can fall out of alignment or refuse to lock properly. This is particularly likely if you live in an area prone to harsh climates. Houses in fluctuating climates are more likely to move.
Why are my bifold doors hard to open?
When a bi-fold door leans, the door may be difficult to open or close, and the guide tends to slip out of the head track. This is usually easy to fix. Start by resetting the guide inside the track if it has come out, then close the door and check the gap between the edge of the door and the track.
Why do bifold doors pop open?
Slide the bifold door open. Look up at the end of the door track where the door stop, called a snugger, is located. The snugger is a small plastic piece with a metal spring inside it. If the doors push against the spring too strongly, the doors pop back open.
Can you have 2 bifold doors?
Despite the fact you can’t have a full bifold in a small space, you can still enjoy the flexibility of a two-pane bifold door. This is a door that has two leaves, or panes, with a hinge between them. Like a bifold, the two-pane variant opens at the extreme left or right edge, and can be folded on itself.
What is the rough opening size for a 48 inch bifold door?
The required size of the finished opening for a 48-by-80-inch door is 48 by 82 inches. The rough opening should be 49 by 82 for a 48-by-80-inch door. This allows for 1/2-inch-thick drywall on both sides and at the top, 80 inches for the doors and hardware, and a 1-to- 1 1/2-inch space under the door.
What is the standard height of a bifold door?
Standard size bifold doors are usually 2090mm or 2100mm tall, only slighter taller than you’d find when fitting an internal door. Bifold door widths, however, will vary dramatically depending on your aperture, and could be anywhere from 1800mm with two-panel bifold doors, to 4800mm with up to 6 doors!
How much can you trim a Masonite door?
For Molded Panel and Flush doors, you can trim 1/8” off each edge (sides, top and bottom) without affecting your warranty. For Wood Panel, MDF and French doors, you can trim 1/4” off each side and 1” off the bottom of the door without affecting your warranty.
How much can you cut off the bottom of a hollow core bifold door?
How Much Can You Trim off a Hollow Core Door? Removing an inch or so from a hollow core door to allow for a thicker carpet, misread tape measure or wonky doorframe will be fine. However, cut off too much – roughly over 2 inches – and you may notice that the edge of the door is no longer solid.